search

ViewSonic PJ1065-2 User's Guide Page 22

  • Download
  • Add to my manuals
  • Print
  • Page
    / 30
  • Table of contents
  • TROUBLESHOOTING
    •
  • BOOKMARKS
    • Rated. / 5. Based on customer reviews
Page view 21
20 ViewSonic PJ1065
TROUBLESHOOTING
OSD Message
The messages as described below may appear on the screen at power ON. Take the appropriate mea-
sures when such messages appear.
Table 9: OSD Message
NOTE:
(*1) This message is cleared automatically after approximately three minutes, and appears every
time power is switched ON.
(*2) The unit has a function to turn the power off which will be active when the usage time reaches
2000 hr. However the life of lamp might be much different, so that it might happen that a lamp is cut
off before the function is active.
Message Contents
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
(*
1)
The usage time of lamp will be reaching 2000 hr shortly (*2).
It is recommended to replace the lamp soon. Prepare a new lamp
as replacement.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL TURN
OFF
AFTER
**
hr.
(*
1)
The usage time of lamp will be reaching 2000 hr shortly.
It is recommended to replace the lamp within * * hours (*2).
It might happen that the lamp is cut off before * * hr by any
chance. Power will be switched OFF automatically in * * hours.
Replace the lamp as shown on p. 17-18, “Lamp.” Always reset
the lamp timer after replacing the lamp.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL
TURN OFF
AFTER 0 hr.
The usage time of lamp is about to reach. Power will be switched
OFF in a few minutes (*2).
Switch power OFF immediately and replace the lamp as shown
on p. 17-18, “Lamp.” Always reset the lamp timer after replacing
the lamp.
NO INPUT IS DETECTED
ON
***
No input signal found.
Check the signal input connections and signal sources.
SYNC IS OUT OF RANGE
ON
***
The horizontal or vertical frequency of the input signal is not
within the specified range.
Check the specifications of the equipment and the signal source.
CHECK THE AIR FLOW
The internal temperature has risen.
Switch power OFF, and wait 20 minutes until the equipment cools
down.
Check the following and Switch power ON again.
* Are the ventilation openings blocked.
* Is the air filter dirty.
* Is the ambient temperature higher than 35°C.
Page view 21
1 2 ... 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Comments to this Manuals

No comments
Related products and manuals for Projectors ViewSonic PJ1065-2
Projectors ViewSonic PJD6212 User Manual   (41 pages)
Projectors ViewSonic LiteBird PJ853 User's Guide   (24 pages)
Projectors ViewSonic PJ551 - XGA LCD Projector Service Manual   (62 pages)
Projectors ViewSonic PJD8353S User Manual   (3 pages)
Projectors ViewSonic VS11990 User Manual   (52 pages)
Projectors ViewSonic PJD6381 - 2500 Lumens XGA DLP Ultra Short-Throw Projector User Manual   (8 pages)
Projectors ViewSonic PJD2121 - SVGA DLP Projector User Manual   (36 pages)
Projectors ViewSonic VS11861 User Manual   (1 pages)
Projectors ViewSonic PJD6211P Service Manual   (60 pages)
Projectors ViewSonic VS13648 User Manual   (50 pages)
Projectors ViewSonic PJ502 User Manual   (2 pages)
Projectors ViewSonic PJD6543w User Manual   (91 pages)
Projectors ViewSonic VS12680 User Manual   (13 pages)
Projectors ViewSonic PJD6210-WH User Manual   (2 pages)
Projectors ViewSonic VS11611 User's Guide   (75 pages)
Projectors ViewSonic PJD6212 User Manual   (41 pages)
Projectors ViewSonic ViewDock PJ258D User Manual   (2 pages)
Projectors ViewSonic LiteBird PJ853 User Manual   (2 pages)
Projectors ViewSonic VA2431w User Manual   (1 pages)
Projectors ViewSonic VS13306 User Manual   (2 pages)
  • Edbak Identa VCAN Blue Coat Mobee Technology
  • LST Unknown Harman Kardon Car video systems Dell Disk arrays Sharp Print & Scan Microsoft Tablets
  • Dell 3560 Sony DSX-A30 Carrier 33CS Gardman 5 Tier growhouse Dayton WT3
  • TEAC CD-P1260 Owner's Manual AEG L9FEA69S User Manual Massive Audio M8 Specifications Robomow MC300 User Manual Att E580-2 User Manual