ViewSonic®Model No. : VS13729PJD6211PDLP Projector- User Guide- Guide de l’utilisateur- Bedienungsanleitung- Guía del usuario- Guida dell’utente- Guia
Rear View Connection portsAC power socketKensington lockRear IR remote control sensorVentilation holes (exhaust)Security barBottom ViewCeiling mount h
Using the ProductControl PanelLEDButton FunctionPower (Power LED indicator)Refer to “LED Indicator Messages”.TEMP (Temperature LED indicator)Refer to
Connection PortsCOMPUTER IN 1Connect image input signal (analog RGB or component) to this jack.COMPUTER IN 2Connect image input signal (analog RGB or
Remote ControlPOWERTurn the projector on or off.Four directional buttonsUse four directional buttons toselect items or make adjustmentsto your selecti
Replacing the BatteryFor the first time use:Remove the transparent insulation tape by pullingit before use.For battery change:1. Push the catch to the
Remote Control OperationPoint the remote control at the infrared remote sensor and press a button. Operating the projector fromthe front Operating t
InstallationConnecting the ProjectorAudio Cable S-Video CableVGA Cable (D-Sub to D-Sub) Composite Video CableRS-232 Cable VGA (D-Sub) to HDTV (RCA) Ca
Powering On/Off the ProjectorPowering On the Projector:1. Remove the projector lens cap.2. Complete the AC power cord and peripheral signal cable(s) c
Adjusting the ProjectorAdjusting the Projector HeightThe projector is equipped with an elevator foot to adjust the image height.To raise or lower the
Adjusting Projection Image SizeRefer to the graphic and table below to determine the screen size and projection distance.Screen sizeDiagonal (inch)4 :
CONTENTSIntroduction ...5Projector Features ...
Menu OperationThe projector has multilingual on-screen display menus that allow you to make imageadjustments and change a variety of settings. PJD621
1 Adjustable range and default setting vary depending on signal type.2 This function is only available when the projector is installed an optional fi
How to operate1. Press the MENU button to open the OSD menu.2. When OSD is displayed, use S / T to select any feature in the main menu.3.After selecti
GammaEffect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.3D Sync Off: Disable 3D function 3D-Vision: For
Signal TypeSpecify the source to the COMPUTER IN 1/COMPUTER IN 2 terminal that you wish toproject. Auto : Automatically detect the input signal type
Set or change the password. When the password function is added, image projectionwill require to input the preset password when turning on the project
MaintenanceThe projector needs proper maintenance. You should keep the lens clean as dust, dirtor spots will project on the screen and diminish image
Replacing the LampAs the projector operates over time, the brightness of the projector lamp graduallydecreases and the lamp becomes more susceptible t
1. Turn off the projector.2. If the projector is installed in a ceiling mount, remove it3. Unplug the power cord.4. Loosen the screw in the side of th
SpecificationsDisplay system Single 0.55" DLP panelResolution XGA (1024 × 768)Zoom 1.1XF/No. 2.51 - 2.69Focal length 21.95 - 24.18mmScreen size 2
Compliance InformationFCC StatementThis device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this devi
PJD6211P28ViewSonicAppendixLED Indicator MessagesLED Type Color Status MeaningPower LED Blue FlashThe projector is in standby mode.Lamp LED Red O
Compatibility ModesComputer: Compatibility Resolution H-Sync [KHz] V-Sync [Hz]VGA 640 x 480 24.6 50.031.5 59.937.9 72.837.5 75.043.3 85.0640 x 480 @ 1
Video: Signal Horizontal Frequency (kHz) Vertical Frequency (Hz)1080i 33.8 60.01080i 28.1 50.01080p 67.5 60.01080p 56.3 50.0720p 45.0 60.0720p 37.5 5
TroubleshootingRefer to the symptoms and measures listed below before sending the projector forrepairs. If the problem persists, contact your local re
RS-232 Command and ConfigurationBaud Rate:19200 Parity Bit:none Data Bit:8 Stop Bit:1 Assign Port:COM1NameOperation typeCRCHeader Command Response
D-Sub 9 pin11 CD2RXD3TXD4DTR5GND6DSR7RTS8CTS9RI Wire ListC1 COLOR C21Black 12Brown 23Red 34 Orange 45 Yellow 56Green 67Blu
IR Control Code Key Format Byte1 Byte2 Byte3 Byte4Power NEC 83 F4 13 87Source NEC 83 F4 13 02Up NEC 83 F4 13 82Down NEC 83 F4 13 85Left NEC 83 F4 13 8
Customer SupportFor technical support or product service, see the table below or contact your reseller.Note : You will need the product serial number.
Limited WarrantyVIEWSONIC® PROJECTORWhat the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, und
h. Use of supplies or parts not meeting ViewSonic’s specications. i. Normal wear and tear. j. Any other cause which does not relate to a produ
Important Safety Instructions1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not
Mexico Limited WarrantyVIEWSONIC® PROJECTORWhat the warranty covers:ViewSonic warrants its products to be free from defects in material and workmanshi
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:Name, address, of manufacturer and importers:Méxi
Declaration of RoHS ComplianceThis product has been designed and manufactured in compliance with Directive 2002/95/EC of the European Parliament and t
Copyright InformationCopyright© ViewSonic® Corporation, 2010. All rights reserved.Macintosh and Power Macintosh are registered trademarks of Apple Inc
IntroductionProjector FeaturesThe projector integrates high-performance optical engine projection and a user - friendlydesign to deliver high reliabil
Package ContentsWhen you unpack the projector, make sure you have all these components:Optional accessoriesProjector with Lens Cap AC Power Cord Remot
Projector OverviewFront ViewLens cap Filter coverElevator button SpeakerLens cap strap Focus ringProjection lens Zoom ringFront IR remote control sens
Comments to this Manuals